Skip to ContentSkip to Navigation
Part of University of Groningen
Science LinXScience Linx News

Green ink for 3D prints in filmed article

13 September 2018

A collaborative project between the UG, NHL Stenden University of Applied Sciences and two businesses has produced a ‘green’ ink for a special type of 3D printer. An academic article about this was published at the start of the year and the experiment has also now been filmed for the Journal of Visualized Experiments (JoVE).

Katja Loos | Photo UG
Katja Loos | Photo UG

JoVE is an online journal that aims to make it possible for people to see experiments. A regular academic article usually provides a description of how something was done, but JoVE believes that moving pictures can be useful: they make it easier for the viewer to repeat an experiment. The UG’s Department of Polymer Chemistry has already had an article visualized by JoVE.

Short lines of communication

The JoVE article, which was published on 13 September 2018, is about the materials used by a form of 3D printing known as stereolithography. Stereolithographic printers don’t work with a filament, a plastic thread that melts in the print head, but instead with a liquid that hardens when it comes into contact with UV laser light. This type of 3D printer was invented in the 1980s. But whereas ‘green’ filaments made from renewable materials are widely available, until now there were no green materials for stereolithographic printers.

The UG, NHL Stenden and two companies joined forces to investigate this, with the support of the Province of Friesland, among others. ‘In polymer chemistry, we are good at making and studying the material, whereas at NHL Stenden they have more experience with using plastics and the printers’, Professor of Polymer Chemistry Katja Loos explains.

Vincent Voet | Photo Voet
Vincent Voet | Photo Voet

Vincent Voet is a research lecturer in sustainable plastics at NHL Stenden in Emmen. He is a former PhD student of Loos, so the lines of communication were short. Voet explains what you need in order to make a new printer fluid: ‘We made an acrylate fluid. To do this you need oligomers, which form a network of chains, monomers that serve as a thinner and a UV-sensitive initiator that gets the polymerization started.’

The trick is to get the right ratio of components. The fluid mustn’t be too thick or too thin, and the polymerization must deliver a product that is strong enough. For the new product, the components needed to be made from organic materials wherever possible.

Dentist

Voet: ‘For decades, this kind of fluid has been made from fossil oil. But we used materials made from plant oil. These are different compounds with a different chemical structure.’ The adaptations delivered a good result, with between 34 and 67% of the carbon atoms coming from an organic source. The aim is to increase this, says Voet, ‘but there isn’t a green alternative to all the components as yet.’ For their experiments, the researchers used materials that are commercially available, but in a follow-up study they will also synthesize molecules from plant-based waste in the lab.

The collaboration with NHL Stenden and businesses from the plastic and 3D printer industry was fruitful, says Loos. ‘Two PhD students are now working on a comparable project, one at NHL Stenden and one at the UG.’ ‘We complement each other well,’ says Voet. ‘And there have already been interesting reactions to the study.’ He talks about how an American company that makes pigments contacted him to see if colour prints could be also made with ‘green materials’. ‘And a French chocolatier contacted us, as did a dentist who wondered if you could use our print fluid for fillings.’

The JoVE film shows how the 3D printer fluid is made and how it is used in the printer. The fluid’s structure is then examined under an electron microscope. The researchers themselves carry out the steps of the process and describe what they are doing. This means that fellow researchers, and perhaps also lovers of this form of 3D printing, can also try it out.

The companies involved in the project were SymbioShape from Leeuwarden and KNN Bioplastic from Groningen.

See also the online publicatie in JoVE
The original article was published i in ACS Omega in February 2018

Last modified:19 September 2018 4.48 p.m.
printView this page in: Nederlands

More news

  • 27 May 2019

    Heropening Universiteitsmuseum tijdens 81e lustrum RUG

    Het Universiteitsmuseum Groningen heropent op donderdag 6 juni met twee nieuwe tentoonstellingen: de speciaal voor het RUG-lustrum samengestelde tentoonstelling Ruimteschip Aarde en de spannende Dead Zoo. Daarnaast wordt het boek De rebelse held van...

  • 24 May 2019

    Three UG researchers win Vidi grants

    The Netherlands Organisation for Scientific Research (NWO) has awarded an EUR 800,000 Vidi grant each to 86 experienced researchers. Four of these conduct their research at just one faculty at the University of Groningen (UG): the Faculty of Science...

  • 24 May 2019

    First edition of Top HR Leadership Programme successfully completed

    The University of Groningen Business School (UGBS) and the In the LEAD centre of expertise at the University of Groningen are looking back on a successful first edition of the Top HR Leadership programme. On 21 May, eight top HR professionals with different...